The manual doesn’t mention any lane sharing between the SATA ports and M.2, although it’s not clear that there isn’t any.Īs we continue right, we go over the chipset heatsink and end up at the right edge. The middle M.2 supports both PCIe- and SATA-based modules, while the bottom is PCIe only. The top socket supports PCIe-based drives up to 110mm, while the bottom sockets support up to 80mm modules. The top is PCIe 4.0 x4 and the bottom two are PCIe 3.0 x4. On the M.2 storage front, the EVGA sports three sockets. The bottom slot runs PCIe 3.0 x1 speeds and connects through the chipset. This configuration supports Nvidia 2-Way SLI and AMD 2-Way Crossfire. With both slots occupied, it breaks down to x8/x8. The top slot is wired for x16, while the bottom is a maximum of x8. Starting with the PCIe slots, both full-length slots are CPU connected and support PCIe 4.0 using a Rocket Lakeprocessor. In the middle of the board we find three PCIe slots (two full-length, one x4) and three M.2 sockets, which is typical for this class of board. Although the last-gen audio solution will be satisfactory for all but the most critical of listeners, I still would like to have seen the 4000 series codec used. On the left, hidden under a shroud, is the Realtek ALC1220 codec and four large Rennic audio capacitors. ![]() Z590 adds a bit of eye candy, with large heatsinks covering up the M.2 sockets and chipset. ![]() Looking at the bottom half of the board, this is where we saw the most significant difference in appearance from the last-gen FTW WIFI. Finally, just below the ATX connector is the front panel USB 3.2 Gen2 port. This allows for a cleaner look, as the thick ATX cable wouldn’t stick straight up as it does on most other motherboards. Moving to the right edge you’ll find the 24-pin ATX connector, which is oriented 90 degrees from the standard orientation, in typical EVGA fashion. For the extreme overclocker or someone who uses an open chassis, this is an excellent value add. There’s also a vertically oriented USB port that means you don’t have to reach around the back to the rear IO area to plug in a USB stick. The last two features are great for those who use the board on an open chassis. Additionally, there are two buttons here: one for power on/off, the other for resetting the system. There are three additional 4-pin fan headers, the debug LED for troubleshooting POST issues and a handy USB BIOS update port. As always, your mileage may vary in reaching those speeds as it depends on the CPU’s ability and the kit you choose.Ĭontinuing right, there’s quite a bit going on this part of the board. The Z590 FTW supports 128 GB of RAM, with speeds listed up to DDR4 5100+(OC). Just to the right of the socket area are four DRAM slots. The finned VRM heatsinks do an excellent job at keeping temperatures in order and look good in the process. This should be plenty of power to support your fans and water cooling endeavors. Seven support up to 2A/24W of power, while the Pump header is 3A/36W. Just to the right of that is the first (of eight) fan headers. To the right are two EPS power connectors: An 8-pin (required) and 4-pin (optional) feeds the CPU. A simple frosted cover lets the saturated but not terribly bright RGB elements shine through. Including a USB stick for drivers instead of a CD is a nice touch, which we wish were more common.įocusing on the top half of the board, we get a closer look at the plastic IO cover that contains the RGB lighting. Below is a complete list of all included extras. (1) Intel AX201 (WiFi-6, MU-MIMO, OFDMA, BT 5.2)Īlong with the motherboard, the box includes the basics, but enough to get you started. ![]() (6) SATA3 6 Gbps *Supports RAID 0, 1, 5 and 10
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |